Serving the Pueblo area  ·  (719) 467-3181  ·  Open Mon-Sun 7am-7pm
📞 (719) 467-3181 Free Quote

Metal Roofing in Colorado City, CO (81019) · Local Professionals

Pueblo Metal Roofing · Fast response in Colorado City and the Pueblo area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+232Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Colorado City sits up on the high dry ground northwest of Pueblo, where the wind comes off the Wet Mountains and hits every roof on the ridge. Most homes here are scattered on large lots, a mix of ranch houses, manufactured homes, and newer builds with a few farm and shop buildings mixed in, and the wind and hail out here do not give roofing an easy pass.

That is why folks in 81019 call Pueblo Metal Roofing. We know how panels behave on an exposed lot near Lake Pueblo and how hail and spring wind work on the ridgelines around Colorado City. We install, repair, and replace metal roofs built for this exact climate.

Metal Roofing in Colorado City (81019)

Colorado City is not a tight grid of city lots. Homes are spread out on larger parcels, often with gravel drives, open exposure, and a lot of wind. The ground is dry and sandy in places, which matters for drainage and for how we stage materials. Many roofs here are low-slope or have simple gable lines, which is a good fit for standing seam and corrugated panels. We also see older outbuildings and shops that need exposed-fastener metal, and we handle those the same way we handle a house: correct fasteners, proper flashing, and a clean finish. The wind is the big one. It gets under lifted panels and failed fasteners fast, so we pay close attention to screw patterns, seam engagement, and edge metal.

Our team has worked roofs across Pueblo County, from the older brick homes near Mesa Junction and the Bessemer mill cottages to the newer stucco subdivisions in Pueblo West and the farm buildings out toward Boone and Rye. In Colorado City we bring that same approach: metal roofing sized and fastened for high, dry, windy ground.

Our services in Colorado City

How a Job Works in Colorado City

Step 1: You call us at (719) 467-3181 or send a request, and we set up a free on-site assessment. We look at the roof, the deck, the flashing, and how the wind hits the house. We check for lifted panels, loose screws, seam separation, and any leak points. You get a straight answer and a written estimate.

Step 2: We schedule the work and pull the permit if the job needs one through the local building department. On Colorado City lots we plan for material delivery and staging, since driveways and access vary a lot from property to property. If there is an HOA or a historic review in play, we coordinate on panel profile and color before anything is ordered. Then we tear off or retrofit, install the underlayment and flashing, and set the panels or shingles.

Step 3: We clean up. Magnets for screws, a full sweep of the yard and driveway, and a final walkthrough with you. We show you what we did, how the flashing and fasteners look, and what to watch for. We leave your property clean and we do not leave debris behind.

Pricing in Colorado City depends on the roof, not on a generic number. As a ballpark, metal roof installation starts around $8 per square foot, standing seam starts around $10, metal roof replacement around $9, and a retrofit over existing shingles around $7. Repairs start around $450, leak repairs around $450, and screw replacement and re-fastening around $750. Corrugated and ribbed panel roofing starts around $5.50, metal shingle and stone-coated steel around $9, and copper or specialty metal around $20. Coating and painting starts around $2.50, flashing and chimney or skylight repair around $600, snow guards around $1,200, and gutters around $9 per linear foot. The real cost factors are roof size and pitch, how many layers are coming off, access and staging on your lot, the condition of the deck and flashing, and how urgent the job is. Call (719) 467-3181 for a free estimate and a real number for your roof.

My place near Lake Pueblo gets hammered by wind. Will a metal roof hold up better than shingles out here?
Yes, generally. Metal panels and fasteners are made for high-wind exposure, and standing seam in particular handles wind uplift well when it is installed with the right clip and fastener pattern. The key is the install: correct edge metal, proper seam engagement, and screws set to the right torque. We size the system for the exposure on your lot, not a one-size-fits-all spec.
A storm just peeled back panels on my roof in Colorado City. How fast can you get out?
Call us at (719) 467-3181 and we will get an inspection scheduled as soon as we can. For active leaks or lifted panels we focus first on stopping water and securing the roof, then we document the damage and give you a repair or replacement estimate. We do not promise insurance coverage, but we do provide the photos and paperwork your insurer will ask for.
What does a typical metal roof replacement cost in Colorado City compared to a repair?
It depends on the size and condition of the roof. A repair often starts around $450, while a full replacement starts around $9 per square foot for metal roof replacement and around $8 per square foot for installation. Larger homes, steep pitches, multiple layers to remove, and difficult access push the number up. We give you a free estimate so you can compare repair versus replacement honestly.
Do I need a permit for a metal roof in Colorado City, and who handles it?
Roofing permits are commonly required for a full replacement or re-roof, and the rules vary by jurisdiction. We check with the local building department for your address and handle the permit as part of the job. We also confirm whether a recover over existing shingles is allowed, since code limits how many existing layers you can leave in place.
My HOA has rules about roof color and panel style. Can you work with that?
Yes. We ask for your HOA or design review requirements before we order anything, and we help you pick a panel profile and color that meets them. If there is a property line question with a neighbor about drainage or overhang, we flag it early and keep the work within your lot lines.
Are you insured for work on my property in Colorado City?
We are fully insured, with general liability and workers' compensation coverage. That protects you and your property if anything goes wrong on the job. We are happy to provide proof of insurance before we start.
What should I do each season to keep a metal roof in good shape in this climate?
Inspect after the spring and fall wind seasons, and again after summer hail. Look for loose or backed-out screws, lifted panels, and sealant that has dried out at flashing and penetrations. Keep gutters clear so snowmelt and rain drain away from the eaves. If you see anything that worries you, call us at (719) 467-3181 for a free inspection.
Why choose us?

Trusted professionals in Pueblo

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Pueblo

All your work handled by qualified professionals in Pueblo

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

232+ Verified Client Reviews in Pueblo

⭐⭐⭐⭐⭐ 4.9/5 · 232 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Pueblo · Response within 24h · No commitment · ☎ (719) 467-3181

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Pueblo ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm